Is this a hardware or a software issue?

Network failures can look like either layer depending on the symptom. The discriminator is the resolution of the symptom to the recommended fix: if applying the steps under "How to fix it" eliminates the symptom, this is a software/configuration class issue regardless of the hardware it surfaced on. Repeat the fix on a fresh node to confirm.

How long does the fix typically take?

Most resolutions from this entry take 10 to 30 minutes of engineer time once the diagnosis is confirmed. Long fixes come from skipping the diagnosis step and chasing apparent symptoms (validation drift, memory growth, slow throughput) instead of the actual root cause listed above. Apply the fix in a small experiment first, then roll it forward.

Does this affect inference or only training?

Primarily this is a network failure observed during training, but the same misconfiguration can leak into downstream evaluation and serving. Treat the prevention checklist as a guardrail: any pipeline that touches a trained checkpoint should re-validate the failure mode before promoting the model.

What's the cheapest way to confirm this is the problem?

Cheapest signal: reproduce the symptom on a 1-GPU toy run with the same configuration. If the toy run exhibits the same behavior, the cause is the configuration rather than the cluster. If only the multi-GPU run is affected, the failure is a distributed interaction, so NCCL is the most likely layer to inspect.

Can the Denpex platform detect this automatically?

Yes. Denpex correlates the symptoms in this entry against your training logs in real time and surfaces the failure taxonomy, root cause, and exact remediation command on the console. Three full diagnoses are included free during signup, and the encyclopedia entry you are reading is generated from the same signal library that powers the platform.

What related failures should I check next?

Closely related failures cluster around #NCCL Network Initialization Hang. After applying this fix, validate against the related entries below to confirm no overlapping cause is masking as this one. Engineers routinely discover that the dominant failure mode is actually a second, sibling failure compounded on top.

Will this recur after the fix?

Applied once with the prevention checklist, this failure does not recur under normal operation. The recurring variant most engineers encounter is the re-emergence of the same symptom on a different model or stack after NCCL Network Initialization Hang is upgraded. Pin compatible versions and rerun the prevention smoke test on every dependency change.

Is there a fingerprint I can monitor?

Yes. Training hangs immediately upon starting, during init_process_group or the very first collective operation. is the highest-signal fingerprint. Wire a metric or alert on that signal (or its absence after the fix) so you can detect the recurrence automatically. The Denpex platform encodes this exact fingerprint and surfaces it directly in the dashboard.

What is the official documentation that covers this?

Reference documentation is listed in the References section at the bottom of this entry. The most authoritative URLs are the upstream framework docs and the issue trackers cited; the Denpex entry synthesizes both into the executive, engineer, and on-call perspectives so each audience can act without reading every linked source.

Does this entry include working code?

Yes. The "Code Examples" section contains copy-paste-ready snippets that target the most common stacks (PyTorch, Hugging Face Trainer, DeepSpeed, Megatron-LM, vLLM/Transformers). Each snippet is annotated with why it works so you can adapt the pattern to your own framework without losing fidelity.

NCCL Watchdog Timeout due to Incorrect Network Interface

Q: What does this failure look like in production?

In production this failure typically appears during the first tens-to-hundreds of training steps: loss curves become non-monotonic, validation metrics plateau above the baseline, and downstream checkpoints either diverge or fail to improve. Engineers frequently misread it as data drift when the underlying mechanism is nodes have multiple network interfaces (e.g., a high-speed infiniband/roce interface, a standard ethernet interface, and a docker bridge). nccl heuristically picks an interface, often picking a local virtual interface (like docker0) that cannot route traffic to other nodes. processes attempt to form the nccl ring but packets are dropped, leading to a hang.. Validating against the symptom list in this entry is the fastest way to confirm the diagnosis.

Q: How does this scale from 1 GPU to 1000 GPUs?

At single-GPU scale the symptom usually looks like slow convergence or a single anomalous loss value. At 64+ GPU scale, distributed interactions amplify nodes have multiple network interfaces (e.g., a high-speed infiniband/roce interface, a standard ethernet interface, and a docker bridge). nccl heuristically picks an interface, often picking a local virtual interface (like docker0) that cannot route traffic to other nodes. processes attempt to form the nccl ring but packets are dropped, leading to a hang. through collectives, and the failure can manifest as a full job abort. Always reproduce the fix at the smallest cluster configuration that still exhibits the symptom before promoting to production scale.

Nodes have multiple network interfaces (e.g., a high-speed InfiniBand/RoCE interface, a standard ethernet interface, and a Docker bridge). NCCL heuristically picks an interface, often picking a local virtual interface (like docker0) that cannot route traffic to other nodes. Processes attempt to form the NCCL ring but packets are dropped, leading to a hang.

Quick answer

Nodes have multiple network interfaces (e.

Symptom: NCCL WARN Call to connect returned Connection refused
Root cause: Nodes have multiple network interfaces (e.g., a high-speed InfiniBand/RoCE interface, a standard ethernet interface, and a Docker bridge).
Recommended fix: NCCL_SOCKET_IFNAME=eth0
How Denpex helps: Denpex matches NCCL Watchdog Timeout due to Incorrect Network Interface across every rank in a distributed run and reports which rank failed first, so you act on the initiating node instead of the loudest one.

Network#NCCL Network Initialization Hang

What this failure is

NCCL Watchdog Timeout due to Incorrect Network Interface is a Network failure seen during ML training runs. Nodes have multiple network interfaces (e.g., a high-speed InfiniBand/RoCE interface, a standard ethernet interface, and a Docker bridge). NCCL heuristically picks an interface, often picking a local virtual interface (like docker0) that cannot route traffic to other nodes. Processes attempt to form the NCCL ring but packets are dropped, leading to a hang. Common tags: NCCL Network Initialization Hang.

Live diagnosis, no signup

Is this what broke your run? Paste your log.

You're reading about NCCL Watchdog Timeout due to Incorrect Network Interface. Paste your own crash log or traceback below and get the real root cause for YOUR run, not this generic entry. No account, no card. Logs are masked at ingress and never saved to account history.

training_logs.txt

No log to hand? Try one:

3 free diagnoses/day

Want 14 days on the Scale plan?

Request an evaluation code. A verified workplace organization activates up to 50 diagnoses a day, alerts, history, and follow-up questions. No credit card or automatic subscription.

Evaluate one incident

Why it happens (the mechanism)

It appears as a generic hang or timeout, but it's a fundamental failure to establish TCP/IP connectivity over the chosen interface.

What you'll observe

Watchdog caught collective operation timeout
NCCL WARN Call to connect returned Connection refused

Common symptoms and what they mean

Symptom	Why it happens
Training hangs immediately upon starting, during init_process_group or the very first collective operation.	Nodes have multiple network interfaces (e.g., a high-speed InfiniBand/RoCE interface, a standard ethernet interface, and a Docker bridge). NCCL heuristically picks an interface, often picking a local virtual interface (like docker0) that cannot route traffic to other nodes. Processes attempt to form the NCCL ring but packets are dropped, leading to a hang.
The hang lasts exactly as long as the timeout configured in init_process_group.	Nodes have multiple network interfaces (e.g., a high-speed InfiniBand/RoCE interface, a standard ethernet interface, and a Docker bridge). NCCL heuristically picks an interface, often picking a local virtual interface (like docker0) that cannot route traffic to other nodes. Processes attempt to form the NCCL ring but packets are dropped, leading to a hang.

Which systems are affected

NCCL
Docker
Kubernetes

How to confirm this is the problem

Use this checklist to test the hypothesis against a small reproduction. No single line proves the root cause, so preserve the preceding events and compare one variable at a time.

✓Run ifconfig or ip a on the nodes to list interfaces.
✓Set NCCL_DEBUG=INFO and check the logs for which NET/Socket interface NCCL is binding to.

Searchable error signature

search key

NCCL WARN Call to connect returned Connection refused
Watchdog caught collective operation timeout

Use this text as a lookup key in logs and upstream issue trackers. It is not presented as a captured customer log. Confirm the cause from your own preceding events, versions, configuration and the cited references.

The fix and the prevention pattern

The root cause is on this page and stays free. A free account adds the exact remediation steps, saved history, and the fix on every entry in the encyclopedia.

No credit card. Daily allowance follows verified trust tier. Instant access.

Diagnose this failure in VS Code

Select the traceback or open the failed terminal, then run Denpex locally to see the initiating rank, collateral failures, exact fix, and verification command without uploading the log.

Install the free VS Code extension

NCCL errors in context

NCCL is where a distributed job reports failure, which is not the same as where it failed. The hub lists every common NCCL error next to what it actually indicates, and the environment variables that tell them apart.

Compare every nccl error side by side

Root cause

Nodes have multiple network interfaces (e.g., a high-speed InfiniBand/RoCE interface, a standard ethernet interface, and a Docker bridge). NCCL heuristically picks an interface, often picking a local virtual interface (like docker0) that cannot route traffic to other nodes. Processes attempt to form the NCCL ring but packets are dropped, leading to a hang.

The fix and how to prevent it

Evaluate Denpex on your own logs

Request a Scale evaluation code. A verified workplace organization activates 14 days with up to 50 diagnoses a day. Every account keeps its current diagnosis allowance and gets a verification path. No card or automatic subscription.

References

↗NCCL Troubleshooting - Network Interfaces

Don't just read the fix, diagnose your run

The encyclopedia tells you what went wrong. Denpex tells you what went wrong in YOUR training run. With your logs, your config, and your stack.

Diagnose your logs free Browse all failures

Related Network errors

NCCL Vendor Err 129 (RDMA Timeout)

Network · critical

NCCL RoCEv2 GID Index Mismatch

Network · critical

NCCL Binding to Virtual/Docker Interface

Network · critical

FSDP Ignores User-Defined NCCL Timeout with Device Mesh

Network · critical